HGM High Pressure grinding mill plant
1. Introduction of the grinding mill:
HGM series of Three-Ring & Medium-Speed Micro Powder Grinder(also named HGM High Pressure Micropowder grindier) is a new kind of micro-powder processing equipment, which is invented through more than twenty times experiments and improvements, and based on twenty years of mill manufacture experience while absorbing advanced international machine manufacture techniques. HGM series of Three-Ring & Medium-Speed MicroPowder Grinder is mainly used in processing non-inflammable, non-explosive, brittle material with hardness below six mohs, such as calcite, chalk, limestone, dolomite, kaolin, bentonite, talc, mica, magnesite, pyrophillite, ceyssatite, barite, gypsum, alunite, granite, fluorite, phosphate rock, kalium ore, float stone, more than 200 kinds of materials.
2. Working Principle of the mill:
The motor drives the main shaft and every turnplate through the reducer. The reducer drives dozens of rollers to rotate against race way of ring through pin. Small materials crushed by hammer crusher is transported into hopper by elevator, and then vibrating feeder shall feed material to the central part of upper turnplate evenly. The material falls to circle under the centrifugal force and comes down to raceway of ring to be crushed into powder. After grinded in the first race way, the material goes to the second and third turnplate. The blower inhales the external air into the mill and carries the powder after third turnplate into powder-separator. Turbine in the separator makes the coarse powder drop down and regrinded and the fine powder shall go into cyclone powder collector together with air current and go down through discharge valve as final product; At the same time, air current with a little dusts goes out through blower and muffler after purified by filter.
3. HGM High Pressure Micro Powder Grinder Characteristics:
Three-Ring & Medium-Speed MicroPowder Mill has high efficiency and low cost. Its capacity is raised by 40% compared with airflow mill and mix mill on the condition that the materials, the drive and the fineness of the final powder are the same. The life span of tear & wear parts is more than that of straight impact crusher and turbine mill under the circumstance of same materials and fineness of the final powder. Usually, its life span is more than one year. There is no rolling bearing and screw in the grinding cavity, so as to avoid the damage to the machine caused by tear & wear of bearing and seals and the looseness of screws. The fineness of powder can reach <5μ M with d97 once.
4. Payment & shipping terms
1. Price: FOB USD 1000-90000/set(negotiation)
2. Minimum Order Quanlity(MOQ): 1 set
3. Port: Shanghai; Qingdao
4. Packaging Details: Standard Container, Nude Packs or in Bulk.
5. Delivery Time: 15-30 days
6. Payment Terms: L/C, T/T
7. Supply Ability: 25-35 set per Month
Service Standards of Our Company
Pre-sale:
(1) device model choice.
(2) According to customer's special requirements, design and manufacture of products.
(3) training technical personnel for clients.
(4) the company free of charge to the user on-site engineering and technical personnel planning site for the user to design the best processes and programs.
Sale:
(1) product acceptance.
(2) to help customers develop construction programs.
After-sale:
(1) free to assign a dedicated service personnel, arrived at the scene and guide customers installation.
(2) equipment installation.
(3) on-site training of operators.
(4) complete sets of equipment installed, 1-2 full-time technical staff to stay free of charge to help customers on-site production of 1 month, until the user satisfaction.
Technical parameter:
| Model |
HGM60 |
HGM80 |
HGM100 |
| Average work diameter(mm) |
600 |
800 |
1000 |
| Roller number |
15 |
21 |
27 |
| Ring number |
2 |
2 |
2 |
| Feeding size (mm) |
≤ 10 |
≤ 10 |
≤ 10 |
| Fineness of final product |
μ m |
5-45 |
5-45 |
5-45 |
| mesh |
3250-325 |
3250-325 |
3250-325 |
| capacity (kg/h) |
350-2500 |
600-4000 |
900-6000 |
Electrical machinery power
(kw) |
Main engine |
37 |
55 |
90 |
| Chooses the powder machine |
11 |
18.5 |
30 |
| Air blower |
30 |
45 |
75 |
| Feeding engine |
0.06 |
0.06 |
0.15 |
| Discharge valve |
0.75 |
0.75 |
1.1 |
| Overall dimension(m) |
10× 2× 5.5 |
11.9× 2.7× 5.8 |
14.5× 3.8× 6.3 |
| Main frame weight(kg) |
5200 |
7000 |
9500 |
About us
Zhengzhou General Mining Machinery Co., Ltd was founded in 2004, aiming to serve the need in mining, metallurgy, construction, chemical industry etc. We manufacture TYM brand Mining Machinery which are 100% of our own design, production detection and marketing.
What distinguishes our machine from other 's worldwide is our invention and innovation on practical and easy crushing, milling system. We believe that quality should be integrated into every part of our machine.
Our main products are Powder Grinder, Raymond Grinders, High Pressure Suspention Grinders, High Pressure Micro-powder Grinders, Vertical Shaft Impact Crushers, Impact Crushers, Jaw Crushers, Cone Crushers, Vibrating Screens, Sand Washing Machines, nine series of products with more than 30 kinds of specifications.
They are all designed, produced, manufactured and tested in accordance with the standard of ISO9001: 2000 international quality system standard. Our products are recognized as quality products by technical supervision departments.
Every year, we export our grinders and crushers to South Asia, Africa, South America, middle East and other regions in quantity. And our Machines enjoy a high reputation in the foreign market. We welcome you visit our company, and hope we have chance to cooperate with you. Thank you.
){kind=link}